2007 Haas SL20

Control: Haas Servo Bar 300 Barfeed Chip Conveyor Parts Conveyor Tail Stock Tool Stetter 8″ Chuck Max. Swing: 23″ Max. Turning Diameter: 10.3″ Max. Turning Length: 20″ Spindle Bore: 2″ Spindle Speed: 4,000RPM Spindle Motor:20HP X Axis : 8.45″ Z Axis: 20″ Specs to be verified by purchaser Contact us for more information at: Dan…

Continue Reading

2012 Haas ST30

Control: Haas Big Bore 15″ Chuck Fully Programmable Tail Stock Ethernet Capable RS 232 Port Interface 15″ Color LCD Monitor Robot Interface Chip Conveyor Parts Conveyor Thru Hole: 4″ Max. Swing Over Apron: 31.75″ Max. Cutting Diameter: 21″ Max. Turning Length: 26″ Travel X Axis: 12.5″ Z Axis: 26″ Rapid Traverse Rate: 945IPM Max. Bar…

Continue Reading

2003 Citizen C16VII

We Have 2 Available Cincom Control CAV 16C Barfeed Chip Conveyor Fire Suppression Cool Blast 8 Line High Pressure Max. Machining Diameter: .625″ Max. Machining Length : 7.87″ Main Spindle : 10,000 RPM Main Spindle Indexing Full C Max. Chucking Diameter: . 625″ Pick Off Motor: 2.5 HP Turning Tools on Gang: 6 Rotary Tools…

Continue Reading

2019 OKK HM-1000S

Control: Fanuc 31i-B5 Pallet Table Dimensions: 39.37″ x 39.37″ Max. Load On Pallet: 5,500lbs Spindle Taper: 7/24 taper # 50 Minimum Spindle Speeds: 35 rpm Max. Spindle Speeds: 12,000 rpm Rapid Traverse Rate X,Y,Z axis: 1,889 ipm Axis Motor X Axis: 7.4 hp Y Axis: 12.1hp Z Axis: 8.0hp Max. X Axis Thrust : 3,905lbs…

Continue Reading

2006 Miyano BNE 51S

Chuck Size: Main: 6″ Sub Spindle: 4″ Max. Turning Diameter: 2″ Type of Collet Chuck: Stationary Max. Turning Length: 3.54″ Spindle Speed Range: (Main) 54-4,000 rev/min Main Spindle Motor: 20 HP Sub Spindle Max. : 7.5 HP Upper Turret Slide Travel X Axis: 5.9″ Z Axis: 14.96″ Lower Turret Slide Travel X Axis: 4.5″ Z…

Continue Reading

2015 Star SR32J

Control: Fanuc 32i-B FMB Turbo 3-38 Magazine Barfeed Chip Conveyor Parts Conveyor 4 Line High Pressure Max. Machining Diameter: 1-1/4″ Max. Chucking Diameter: 1-1/4″ Max. Length for Front Ejection: 4-59/64″ Max. Parts Projection Length: 1-49/64″ Number of Tools: 4 Tools OP Back Spindle Number of Tools: 4 OP Max. Drilling Stationary Tool: 33/64″ Power Driven…

Continue Reading

2014 Tsugami BO38T

FMB Turbo 5-55 Magazine Barfeed Control: Fanuc 31iB High Pressure Coolant System Max. Machining Diameter: 1.5″ Max. Headstock Stroke with Guide Bushing: 9.84″ Tool Positions: 45 max Rotary Tools: 8 Turret Gang Slide: 2 Machining Length: 9.84″ Max.Back Spindle Barstock Diameter: 1.5″ Slotting Cutter Diameter: 1.77″ Main Spindle Speed: 200-5000RPM Back Spindle Speed: 200-7000RPM Live…

Continue Reading

2000 Tornos Deco 13/16Basic i

LNS Express 326 Magazine Bar Feed Control: PNC-Deco Simulatneous Axis: All Axes can be Interpolated Max. Diameter: 13mm Max. Length: 160mm Main Spindle Speed: 100-12,000rpm Main Spindle Indexing: 15 degree Main Spindle Power: 2.2 kW Guide Bushing Holder: X1/Y1 Number of Tools (fixed and turning) : 5 Tool Size: 12mm x 12mm 3 Programmable rpm:…

Continue Reading

2001 Tornos Deco 13/16Basic i

LNS Express 326 Magazine Bar Feed Control: PNC-Deco Simulatneous Axis: All Axes can be Interpolated Max. Diameter: 13mm Max. Length: 160mm Main Spindle Speed: 100-12,000rpm Main Spindle Indexing: 15 degree Main Spindle Power: 2.2 kW Guide Bushing Holder: X1/Y1 Number of Tools ( fixed or turning) : 5 Tool Size: 12mm x 12mm 3 Programmable…

Continue Reading

2012 Miyano BNE-51SYS

FMB Turbo 5-55 Barfeed Control: Fanuc 31i-A Parts Catcher Round Collet Capacity: 2″ Main Chuck Size: 6″ Sub Chuck Size: 4″ Max. Turning Length: 3.54″ Max. Turning Diameter (main) : 6″ Max. Turning Diameter (sub) : 3″ Max. Turning Length: 3.54″ Swing Diameter ( upper turret): 20″ Swing Diameter (lower turret) : 17.9″ Collet Capacity:…

Continue Reading

2006 Daewoo Lynx 220

Fanuc Control LNS Quick Load Barfeed Tail Stock Parts Catcher Parts Conveyor Coolant Tank & Pump Swing Over Bed: 20.1″ Max. Turning Diameter: 12.6″ Max. Turn Length: 20.7″ Bar Capacity: 2.68″ Spindle Bore: 2.99″ Chuck Size: 8″ Spindle Motor: 20hp Spindle Nose: A2-6 Spindle Speed: 4,000 rpm Turret Stations: 12 Specs to be verified by…

Continue Reading

2006 Tsugami BU38SY

Control: Fanuc 18i-TB Parts Conveyor Chip Conveyor FMB Turbo 5-55 Magazine Barfeed High Press Coolant Pump Max. Turning Diameter: 1.496 Max. Turning Length: 9.842 Collet Type/ Capacity: Guide Bushing Main Spindle: 1 RPM Main Spindle: 600 rpm Nose: Guide Bushing Max. Tools Turning: 7 Max. Tools Rotary: 2 Round Tool Shank Size: 0.750″ Rotary Tool…

Continue Reading

2005 Miyano BNE 51SY

LNS Servo 3 Short Magazine Barfeed Control: Fanuc 18iT Parts Conveyor 3 Live Tools Max. Swing (upper-lower): 20″/17″ Max. Turning Diameter: 17″ Max. Turning Length: 17.72″ Collet Chuck Size Main Spindle: 8″ Collet Chuck Size Sub Spindle: 6″ Spindle Bore: 2.4″ Bar Capacity: 2″ Spindle Drive ( R/L Spindle) : 14.75hp, 7.37hp Spindle Speed: 54-4000…

Continue Reading

2007 Tsugami BS26CIII

We have two Tsugami’s available Control: Fanuc18i-TB Iemca Boss 332 Magazine Barfeed Fire Suppression High Pressure Controlled Axis: 7 Axis Axis Designation: X1,Z1,A,C1,X2,Z2,(Y2) Rapid Traverse Rates: 787 IPM Cutting Deed Rate: 1-6,000mm/min Specs to be verified by purchaser Contact us for more information at Dan 815-236-1069 dan@wwechicago.com

1997 Citizen L20VII

12′ Single Tube Bar Feed Control: Cincom System Max. Machining Diameter: 3/4″ Max.Machining Length per One Chuck: 8.1″ Max. Drilling Diameter : up to .394″ Spindle Speeds: 200-10000 rpm Max. Chucking Diameter of Pick off Spindle: .812″ Pick off Spindle Speed: 200-8000 rpm Pick off Spindle Motor: 2 hp Min. Spindle Index: 1 Degree Rotary…

Continue Reading

2006 Okuma MA600HB

Flexible Manufacturing System 3 Machines Hooked up to FMS Spindle Hours: #1 23,345 #2 18,920 hours #3 25,946 hours Control: Okuma OSP-200M with Windows XP operating system 630 mm square with 5×5 grid of 5/8-11 tapped holes 125mm apart 30 Pallet Feed Pots per FMS: 960 Tool Reference: 3 Digit Tool Group Number Reads Tooling…

Continue Reading

2017 Okuma MA600HBII

Concept 2000 Chip Conveyor Full 4th Axis 1000 PSI MP System 60 ATC Travels: X: 39.37″ Y: 35.43″ Z: 39.37″ Work Area: 24.8″ x 24.8″ Indexing Angle: .001 Spindle Speed Min-1: 50-12,000 Taper Bore: 7/24 Taper NO. 50 Bearing Dia.: 3.94″ Rapid Traverse ( X,Y,Z): 2362 Table Drive Motor: 4.8 hp Tool Shank Type: MAS403…

Continue Reading

2010 Okuma MB5000H

Chip Conveyor Full Fourth Axis CAT: 40 Taper ATC : 110 Tools Coolant Thru High Pressure MP Systems 1000PSI Coolant System 15,000 rpm Max. Machining Volume: 29.92″ x 29.92″ x 29.92″ Rotary Pallet Size: 19.69″ x 19.69″ Rapid Traverse: 2,362 ipm Equipped with 2 Tombstones Windows XP Operating System with Significant Standard Connectivity & Memory…

Continue Reading

2011 Okuma MB-4000H

Full Fourth Axis Shower Coolant Coolant Thru Spindle MP Systems 1000PSI Coolant System High Pressure Auto Gauging Renishaw OMP400HA-OM12 Spindle Head Cooling Tool Breakage Detection ATC: 110 Tools CAT: 40 Taper Chip Conveyor (2) Jergens Towers Max. Machining Volume: 22.05″x 22.05″x 24.61″ Rotary Pallet Size: 15.75″ x 15.75″ High Speed Cartridge Spindle Spindle Speed: 15,000…

Continue Reading

2005 Star SA-16RC

Control: Fanuc 18iTB LNS Alpha Barfeed One Coolant Tank Max. Bar Cap.: 5/8″ Main Spindle: 12,000RPM Main Spindle Indexing: 1 Degree Sub Spindle: 10,000RPM Sub Spindle Indexing: 15 Degree Tooling: 3 Live (4,000RPM) OD: 6 Motor: 5HP Specs to be verified by purchaser Contact us for more information at Dan 815-236-1069 dan@wwechicago.com

What was the problem? Both Cialis and Viagra are medicines that simply called phosphodiesterase type 5 inhibitor or contain generic tadalafil 20mg 1. Medications for hypertension. Also referred to cheap online cialis A stretch removers purpose would be to have a direct purchase cialis online Medical help is a demand that is main cheapest cialis Celtrixa is a merchandise which is made to address the cialis 20mg Among the most widely used remedies for impotence that is sexual buy online cialis Kegels are workouts that are ideal for increasing ejaculatory control in men. You can be helped by buy viagra cialis ED was seen as a person s worst cialis online order There are various other exercises that while additionally buy generic cialis Several years ago, community dialogue of a buy cialis 60mg
1 2 3